Classes, alerts and Smart Dimming
FlyGo draws controlled and special-use airspace so you always know what is around and above you.
- FAA class airspace (B/C/D/E) and special-use areas (MOA, restricted, warning) for the U.S.
- openAIP airspace for 128 countries: classes A–G, control zones, terminal areas (TMA), danger, restricted and prohibited areas, RMZ/TMZ, FIRs and gliding sectors.
- Areas openAIP gives no class or type of their own — aerial sporting, low flying, temporary reserved, military training — are grouped under Other areas.
openAIP’s data is credited on the map, by the © openAIP mark while its airspaces are drawn, and at the foot of each openAIP airspace’s detail.
Layers ▸ Airspaces is where you choose which of them are drawn, and what happens as you approach one.
What is above a point
Tap the map and open the Airspaces tab of the info card. Above the list, a column draws every airspace at that point at its own height — highest first, in its map colour — with the free bands between them labelled, the terrain filled in, and, in flight, your GPS altitude drawn across.

Tap a bar, or a row, to open that airspace. Its detail carries the same column at full size: the one you opened drawn solid, its neighbours faint, the band under 10,000 ft given most of the height and flight levels above it.

- Limits are read as SFC, AGL, MSL, FL or UNL. A height above ground stands on the terrain at the point, and is dashed where no terrain is downloaded.
- Flight levels are drawn at 1013 hPa, which the footer says.
- Where the data has them, the detail also gives the airspace’s ICAO class, the frequency it publishes, whether it is active by NOTAM or on request, and its hours of operation (UTC).
- Upper airspace above FL250 is counted rather than drawn, and an unlimited ceiling has an open top.
Smart Dimming
With Smart Dimming on, airspace whose vertical limits are far from your current altitude fades back, so the airspace you could actually enter stays the most visible thing on the map.
Alerts
An alert raises a banner at the top of the map — one row per airspace, stacked. Which types raise one is yours to set, under Layers ▸ Airspaces ▸ Alerts.
- Approaching: your track enters the airspace within about three minutes. The row carries the estimate and fades by itself.
- Entering: you are inside it. The row stays until you dismiss it with the ✕ — a safety alert should not disappear unread.
- Leaving: confirmation only, and it goes after a few seconds.
A row names the airspace, its class and vertical limits, what entry requires, and how far its boundary is: the shortest way out, as a distance and a compass sector — which can lie behind you, since it is the nearest edge rather than the one ahead. While you are still approaching, it is the edge you will cross.
- What entry requires follows the class: an ICAO class B, C or D airspace needs a clearance; in the U.S. data, class C and D need two-way radio contact.
- A limit above the ground stands on the terrain under you, or on the nearest aerodrome’s elevation where no terrain is downloaded; with neither, a ceiling above the ground counts as open, so an airspace is never missed.
- A flight level is turned into an altitude with the QNH of the nearest METAR within 100 km, no older than three hours; without one it stays at 1013 hPa.
- Without a GPS altitude — a weak fix, an iPad on Wi-Fi only — only the airspace’s outline is checked, and the row says “GPS altitude unknown, vertical limits not checked”.
Who to call
Where the airspace publishes a frequency of its own, the row carries it — BUDAPEST APP 122.980. Elsewhere, where the aerodrome the airspace belongs to can be identified beyond doubt, the row carries that aerodrome’s frequency, labelled with where it came from — BUDAPEST APP 129.700 (from LHBP).
Opening a row
- Tap the row, or its chevron, to open the airspace — the same detail a tap on the chart opens, with the column of the airspaces over you, its class, frequency, hours and limits.
- It opens at half height, with the map still live above it; pull it up to read on, or swipe it away.
- While a point’s info card is open, the rows step down under it in one line each, so the card’s name and lists stay clear.
- The ✕ dismisses the row.
When no banner appears
- On the ground. Taxiing through your own control zone raises nothing, and neither does the climb out of it.
- At the destination you have selected, once you are within five nautical miles of it: its own control zone and terminal area stay silent, because that is where you are going.
- Class E, F and G, FIR, gliding and Other areas are never alerted. Most VFR flying happens inside them, and a banner for each would be noise. Terminal areas (TMA) and control zones are alerted with the controlled airspace — unless their own class is E, F or G.
- The exception is a zone that needs a call before you enter, whatever its class — an aerodrome traffic zone (ATZ, MATZ) or a traffic information zone or area (TIZ, TIA). It raises a “Radio contact mandatory” banner with the TMZ/RMZ alerts.
← Map layers & charts · All topics · Weather on the map →


